Key takeaways
- Most like-for-like boiler replacements in the GTA land between $6,800 and $14,500 installed, depending on whether you choose a heat-only condensing boiler or a combi.
- A complete new combi mechanical room with manifolds, zoning and controls typically starts around $14,000 and can pass $25,000.
- The boiler itself is often less than half the bill. Venting, piping changes, controls and hot-water strategy drive the rest.
- Size the boiler from a heat-loss calculation, not the old nameplate. Oversized boilers short-cycle, waste gas and wear out early.
- Gas boilers and combis are not covered by Ontario’s Home Renovation Savings rebates, but a smart thermostat is.
If your boiler is more than 15–20 years old, needs repeated repairs, or leaves rooms cold every January, you are probably wondering what a replacement will cost. The honest answer is “it depends”, but it depends on a short list of factors you can understand before anyone quotes you. This guide explains real 2026 price ranges for Ontario, what pushes a quote up or down, and how to compare boiler quotes so you pay for a system that actually works.
We design and install boiler rooms across Richmond Hill, Toronto and York Region, so the advice below comes from what we see on real jobs. Prices are before HST and come from published 2026 Ontario sources, which we link to so you can check them.
How much does a new boiler cost in Ontario in 2026?
Published GTA pricing for 2026 puts most residential boiler installations between roughly $6,800 and $18,500 installed. Where you land in that range depends mainly on the type of boiler and how much of the surrounding system has to change.
| Project type (GTA, 2026) | Typical installed range | What is usually included |
|---|---|---|
| Like-for-like non-condensing, heat-only | $5,500, $7,800 | Remove old unit, similar boiler, reconnect existing piping and venting |
| Standard condensing boiler, heat-only | $6,800, $10,500 | High-efficiency boiler, new PVC venting, condensate drain, basic controls |
| Condensing combi (heat + hot water) | $9,500, $14,500 | Combi boiler, domestic hot-water connections, venting, controls |
| Premium modulating combi | $13,500, $18,500 | High-turndown combi, outdoor reset, upgraded controls and accessories |
| Heat-only boiler converted to combi | $11,500, $15,500 | Removing the old tank, re-piping domestic water, new venting |
| Complete new combi mechanical room | $14,000, $25,000+ | Boiler, manifolds, zoning, pumps, expansion, air/dirt separation, controls |
Sources: GTA installation tiers from RenoHouse (Q2 2026 pricing); combi and mechanical-room ranges from BuildersOntario (prices checked October 2026). Your quote can sit outside these ranges, older homes, tight access and commercial-grade equipment all change the number.
What actually drives the price of a boiler replacement
When two quotes for “a new boiler” differ by $5,000, it is almost never the boiler. It is the scope around it. These are the items to look for on every quote.
1. Boiler type and size
A heat-only condensing boiler costs less than a combi, and a premium modulating combi costs more than an entry-level one. Size matters too, but bigger is not better: a boiler should be sized from a room-by-room heat-loss calculation. A typical 2,000 sq ft frame house from the 1990s might lose only 40,000–60,000 BTU/h on the coldest design day, yet many are fitted with boilers two or three times that size. An oversized boiler turns on and off constantly (short-cycling), which wastes gas and shortens its life.
2. Venting and chimney work
High-efficiency condensing boilers vent through PVC or polypropylene pipe, often out a side wall. If your old boiler used a masonry chimney that other appliances still share, the chimney may need a liner. Published 2026 GTA pricing adds roughly $1,200, $2,800 for a chimney liner when it is needed.
3. Near-boiler piping
Old boilers were often piped in a single loop. Modern condensing and combi boilers need the right flow through the heat exchanger, so we usually re-pipe with primary-secondary loops or a low-loss header, add air and dirt separation, and install isolation valves so the boiler can be serviced. This is where a cheap quote cuts corners, and where long-term reliability is won or lost.
4. Domestic hot water strategy
You have three common choices: a combi boiler that makes hot water on demand, a boiler plus indirect tank, or a separate water heater. An indirect tank typically adds $1,500, $2,500 but gives larger homes much more hot water at once. We compare the options in detail in our upcoming guide to combi vs conventional boilers.
5. Zoning and controls
Adding zones, thermostats and outdoor reset increases the price but also comfort and efficiency. If you are adding radiant floor heating at the same time, published GTA pricing puts each radiant zone at roughly $2,500, $6,500 extra. Manifolds and zone controls range from about $500 for a single bathroom to $4,000, $10,000 for a whole house.
6. Gas line, permits and access
Larger boilers sometimes need the gas line upsized ($500, $1,500 is a common range). Municipal permits are usually a few hundred dollars. Tight crawlspaces, long venting runs or boilers on upper floors add labour.
Repair or replace? A simple decision checklist
Replacement is usually the better investment when several of these are true:
- The boiler is 15–20+ years old, or parts are hard to find.
- You have had more than one significant repair in the last two winters.
- The heat exchanger is leaking or badly corroded.
- Some rooms never get warm, or the boiler runs constantly in cold weather.
- You want to add hot water capacity, radiant floors or zoning anyway.
- Gas bills keep rising even though your usage habits have not changed.
If the boiler is younger and the problem is a pump, valve, igniter or control board, a repair is usually the smarter choice. Our boiler maintenance guide explains what a healthy system looks like.
What a good boiler quote should include
Ask every contractor to put these in writing so you can compare quotes fairly:
- Boiler make, model and size, and the heat-loss figure it was sized from.
- Venting route and materials, and whether a chimney liner is included.
- Piping changes: primary-secondary loop or low-loss header, air separator, dirt separator, expansion tank, isolation valves.
- Hot-water plan: combi, indirect tank or separate heater.
- Controls: outdoor reset, thermostats, zone valves or circulators.
- Removal and disposal of the old boiler.
- Permit, gas inspection and commissioning (combustion analysis and setting up the controls).
- Warranty on parts and on workmanship, and who you call if something goes wrong.
Are there rebates for a new boiler in Ontario?
Not for the boiler itself. Ontario’s Home Renovation Savings Program (delivered by Save on Energy and Enbridge Gas) currently focuses on heat pumps, insulation, windows, air sealing and smart thermostats. A smart thermostat rebate is available, and if you are considering a heat pump or hybrid system alongside a boiler, those can qualify. Program terms change, so always check the current page before you buy.
How long does a boiler replacement take?
Most residential replacements take one to two days once the equipment is on site. A full mechanical-room rebuild with zoning and an indirect tank can take three to five days. In winter we plan the work to keep you without heat for as little time as possible, and we can provide temporary heat for longer jobs.
How to keep your new boiler efficient
- Book an annual service before the heating season: combustion check, safety controls, condensate trap and pressure.
- Use outdoor reset so the boiler runs at the lowest water temperature that keeps you comfortable, this is what lets a condensing boiler actually condense.
- Keep the system water clean and treated; dirt is the enemy of modern heat exchangers.
- Do not block combustion air or the condensate drain.
Want to see how we lay out a clean, serviceable boiler room? Read our complete guide to mechanical rooms, or see our boiler room plumbing services.
Get an exact price for your home
Every home is different, so the only accurate number is one based on your house. We visit, check your current system and radiation, calculate your heat loss and give you a written, itemized quote, no pressure. Request a free boiler quote or call (416) 700-3040.
Frequently asked questions
How much does a new boiler cost in Ontario?
Most GTA boiler replacements fall between about $6,800 and $14,500 installed in 2026. A premium combi or a full new mechanical room can cost $14,000–$25,000 or more.
Is a combi boiler cheaper than a boiler with a tank?
A combi usually costs less to install than a boiler plus indirect tank, but larger homes with several bathrooms often get better hot-water performance from the tank option.
How long does a boiler last?
A well-maintained boiler typically lasts 15–20 years or more. Annual servicing and clean system water make the biggest difference.
Are there rebates for gas boilers in Ontario?
Gas boilers and combis are not currently covered by the Home Renovation Savings Program, but smart thermostats and heat pumps are. Check the program page for current terms.
How long does boiler replacement take?
Most residential replacements take one to two days once equipment is on site; a complete mechanical-room rebuild can take three to five days.



